Social Media WireLists42 300It is a simple process to set up a Local Area Network for your Lectrosonics gear, but it requires an understanding of some fundamental concepts to get things setup correctly, consistently.

Before we dive in, If you’re new to connecting to Wireless Designer over a network or have limited experience with networking, our web help tutorial will walk you through some of the basics.

There are two ways to connect to Wireless Designer over a network:

1) Via DCHP, where a router assigns an IP address to the unit/s;

2) Manual IP address entry

Before you begin, assemble the following items. Ideally, you will want to have all of these available, so you can be prepared for whatever you may encounter on the job:


  1. Wire-Lists #41 – 7 Easy Steps to Streaming Online with Lectrosonics Duet
  2. Wire-Lists #40 – Two Steps To Free A Trapped TA-5 Connector
  3. Wire-Lists #39: Distancing with Dante
  4. Wire-Lists #38: Solo Use of the Walk Test Recorder in Wireless Designer in 5 Easy Steps
  5. Wire-Lists #37: Custom Tuning Ranges + 4 Other Cool Things in Wireless Designer
  6. Wire-Lists #36: Additional Tricks for Gain Staging Transmitters and Receivers with Recorders - Part 2
  7. Wire-Lists #35: Two Pros Share Tricks for Gain Staging Transmitters and Receivers with Recorders – Part 1
  8. Wire-Lists #34: A Quick Primer on Setting Audio Input Gain On Wireless Mic Transmitters
  9. Wire-Lists #33: Hey! What's That Sound?
  10. Wire-Lists #32: 4 Quick Tips for Antenna Performance
  11. Wire-Lists #31: Improving Signal to Noise Ratios with PF25 Filters
  12. Wire-Lists #30: Maintaining Social Distancing With Dante-Enabled Equipment
  13. Wire-Lists #29: 4 Tips to Improving Your Wireless Signal To Noise Ratio
  14. Wire-Lists #28: Five Tips for Troubleshooting Wireless Mics
  15. Wire-Lists #27: Advice for Navigating The Block 19/470 Overlap
  16. Wire-Lists #26: Developing Sanitation Protocols for Lav Work:
  17. Wire-Lists #25: 5 Best Practices and Tips for Creating An Online Worship Experience
  18. Wire-Lists #24: Making A Coaxial Dipole Antenna With 6 Items, In 8 Easy Steps
  19. Wire-Lists #23: Phantom Power with M2Rs and Other Receivers, plus 6 Best Practices
  20. Wire-Lists #22: 5 Steps To Getting The Most Out Of The Broadcast Loop
  21. Wire-Lists#21: The #1 Way To Get Flawless Wedding Video Sound With MTCR
  22. Wire-Lists#20: Equipment Disinfection
  23. Wire-Lists#19: ETSI standards, 75 and 50 kHz Deviation for Transmitters, and You
  24. Wire-Lists#18: Everything You Need To Know About Firmware Updates: Part 3
  25. Wire-Lists#17: Everything You Need To Know About Firmware Updates: Part 2
  26. Wire-Lists#16: Everything You Need To Know About Firmware Updates: Part 1
  27. Wire-Lists#15: 4 Things To Check Before We Fix Your Equipment
  28. Wire-Lists#14: My Transmitter Took A Bath! Now What? 5 Steps To Help (plus a bonus tip).
  29. Wire-Lists#13: Three HM Transmitter Hacks (aka “MacGyvers”) for Desperate Situations
  30. Wire-Lists#12: Popular Receiver Antenna Combos
  31. Wire-Lists#11: Popular Transmitter Antenna Combos
  32. Wire-Lists#10: 1 Tip to Identify Types, and 9 Ways To Prevent Wireless Mic RF Drop-Outs
  33. Wire-Lists#9: Three Wireless Designer Tips and Tricks
  34. Wire-Lists#8: Why Are You Holding Your Mic Like That? The Dos and Don’ts of RF Attenuation
  35. Wire-Lists#7: Cold Weather Care for Transmitters, Mics and Receivers
  36. Wire-Lists#6: Preventing Pogo Pin Failure In Your SSM
  37. Wire-Lists#5: 4 Ways to Mangle Your Mic
  38. Wire-Lists#4: SM Transmitter Cleaning – Tips for Battery Doors and 5-Pin Jacks
  39. Wire-Lists#3: Lessons On Battery Care For The Long Ranger
  40. Wire-Lists#2: My Transmitter Doesn’t Work! Three Things To Check
  41. Wire-Lists#1: The 4 Don’ts for Preventing Sick Transmitters