Lectrosonics.com

You are here: Home

Products

#21586

Description: 6 ft. long power cable; locking LZR type plug to stripped and tinned leads.

#21746

Description: 1 ft. DC power cord with locking ring for VR Field, stripped and tinned. See #21747 for 6 ft length.

#21747

Description: 6ft. DC power cord for VR Field, stripped and tinned. See #21746 for 1 ft length.

#21762

Description: Neutrik right angle XLR female connector with 5 selectable cable outlet positions; cast metal housing.

#35679

Description: Lectrosonics screwdriver and adjustment tool for setting transmitter gain and roll-off pots as well as for setting the frequency switches on some older receivers and transmitters.

Description: UHF antenna, right angle BNC. Specify block such as A500RA-24 for block 24. These antennas can be used one block above and below the specified block. Color coded tip per ANSI resistor code.

#BIAST

Description: The BIAS T is used to apply DC power to a coaxial antenna line for remotely powering the UFM230 filter/amp. The DC power applied to the BIAS T (9 to 16 VDC) appears on the input port of the BIAS T to power the UFM230 through the coaxial cable, but is isolated from the output port so it will not be applied to the input of the receiver. The BIAS T is normally placed near the receiver being fed by the coaxial cable, where power is available. The UFM230 filter/amp and antenna are plac ...
Read More...

#DCR15/1A6U

Description: Power supply for D4 System, Venue and VenueField receivers; IEC 60320 C14 inlet (standard 3-pin socket) LZR style coaxial locking outlet plug. 0-240 VAC, 50/60 Hz input; 15 VDC (regulated), 1.6 A max. output, 18 W. (Specify power cord for country of use.) Part # Cord Type 21642 Euro Power Cord - CEE 7/7 (Schuko) plug 21643 UK Power Cord - BS 1363 plug 21644 Australian Power Cord - S3112 plug 21499 USA Power Cord - NEMA 5-15 plug 21511 AC Power ...
Read More...

#MCAXLRATTEN

Description: Balanced XLR male to stripped and tinned leads with a selectable attenuator built into the XLR. Attenuation ratios are -20, -30 and -40 dB. Used to reduce line level signals to mic level inputs into a mixer. By placing the attenuator at the mixer input (male XLR), ground loop noise is greatly reduced since the cable's shield sees line level signals over all its length. Click here for data sheet

#P1196

Description: Retainer clip for Venue, VR Field receiver modules

#PF25 (Specify Block)

Description: Passive in-line RF filter with 25MHz passband. Passive in-line RF filter with 50MHz passband and DC Bias insertion point. Designed for use with VRMWB and VRField WB wide-band receiver systems in cases where the full bandwidth of the receiver is not needed. Specify two-block range when ordering. Specify block when ordering. Click here for Data Sheet

#PF50 (Specify Blocks)

Description: Passive in-line RF filter with 50MHz passband and DC Bias insertion point. Passive in-line RF filter with 50MHz passband and DC Bias insertion point to power remote amplifiers or active antennas. Designed for use with VRMWB and VRField WB wide-band receiver systems in cases where the full bandwidth of the receiver is not needed. Specify contiguous two-block range when ordering. Click here for data sheet

#UFM230

Description: The UFM230 provides a unique solution for antenna systems requiring long cable runs or distribution to multiple receivers or locations. The amplifier in the unit provides 12 dB of gain without attenuation. Gains of 5 dB and 8 dB can also be selected using the supplied attenuators. The built-in filters provide a 230 MHz passband. To determine the correct attenuator for a particular application, first determine the total dB loss due to connectors, splitters, cabling, etc. The abov ...
Read More...