UCR411a
#21425
Description:
6 ft. long power cord, coaxial to stripped and tinned leads. Coaxial plug: ID-.080"; OD-.218"; Depth- .5".
#21472
Description:
6 ft. long power cord; coaxial to stripped and tinned leads. Right angle coaxial plug: ID-.080"; OD-.215"; Depth- .400". Fits all compact receiver models that use CH12 power supply.
#21762
Description:
Neutrik right angle XLR female connector with 5 selectable cable outlet positions; cast metal housing.
#35679
Description:
Lectrosonics screwdriver and adjustment tool for setting transmitter gain and roll-off pots as well as for setting the frequency switches on some older receivers and transmitters.
#A500RA (Specify Block)
Description:
UHF antenna, right angle BNC. Specify block such as A500RA-24 for block 24. These antennas can be used one block above and below the specified block. Color coded tip per ANSI resistor code.
#A500S
Description:
Flexible UHF antenna, straight BNC 470-608. It is now recommended to use the #A8U antenna (block 22) for replacement.
#A8U (Specify Block)
Description:
UHF antenna, straight BNC. Specify block such as A8U-24 for block 24. These antennas can be used one block above and below the specified block. Color coded tip per ANSI resistor code. (See A8Ukit for antenna with caps included)
#A8U Kit
Description:
This is a full size cutting template used to cut the length of the whip for a particular frequency. Lay the uncut antenna on top of this drawing and trim the whip length to the desired frequency.
After cutting the antenna to the desired length, mark the antenna by installing a color cap or sleeve to indicate the color listed in the table below.
The supplied caps can be used several different ways:1) A color cap on the end of the whip2) A color sleeve next to the connector with a ...
Read More...
#ACOAXBNC (Specify Block)
Description:
This coaxial design is approximately 48 inches in overall length, with an right angle BNC connector. The other end is cut to a 1/4 wavelength of the corresponding frequency block with a color band and tag specifying its block. It is especially useful for applications where a small remote antenna is desired.
Coaxial antenna usage guide (PDF)
#AMM-O
Description:
Color coded transmitter antenna caps
#CCMINI
Description:
A soft sided, padded and zippered carrying case for compact wireless systems such as the UCR400, UCR401, and other UCR units.
#CH12
Description:
General purpose AC Adapter, 120VAC in, 12VDC
SPECIFICATIONS:
Input:
120v-60Hz 14W
Output:
13.5v – 300mA
Plug:
ID-.080"; OD-.218"; Depth- .5".
#P1199
Description:
Rain cover for UCR211, UCR411 and UCR411a
#PF25 (Specify Block)
Description:
Passive in-line RF filter with 25MHz passband. Passive in-line RF filter with 50MHz passband and DC Bias insertion point. Designed for use with VRMWB and VRField WB wide-band receiver systems in cases where the full bandwidth of the receiver is not needed. Specify two-block range when ordering. Specify block when ordering.
Click here for Data Sheet
#PF50 (Specify Blocks)
Description:
Passive in-line RF filter with 50MHz passband and DC Bias insertion point. Passive in-line RF filter with 50MHz passband and DC Bias insertion point to power remote amplifiers or active antennas. Designed for use with VRMWB and VRField WB wide-band receiver systems in cases where the full bandwidth of the receiver is not needed. Specify contiguous two-block range when ordering.
Click here for data sheet
#PS2212A
Description:
Power cable, 12", Hirose4 to dual DC coax
#UMCWB
Description:
4 Channel Wideband UHF Diversity Multicouplers
Bandwidth:1) UMCWB: 537 to 768 MHz.2) UMCWBL: 470 to 692 MHz
#VSR1
Description:
Velcro cable strain relief. One piece mounts to receiver and the cable is held between that piece and a mating cover piece.
