Remote Antenna
#21769
Description:
Female BNC to female BNC connector. Commonly used to interface cables to whip antennas or to connect two cables. Minimal loss, 50 Ohms.
#21770
Description:
Coaxial adapter. Male SMA to female BNC. Adapts antennas with male BNC connectors to SMA jacks.
#26311
Description:
Light stand adapter, 1/2" diameter, 6" long, 3/8-16 thread, stainless steel
#26312
Description:
Thread adapter, 1/2" diameter, 1 3/4" long, 3/8"-16 and 1/4"-20 threads, stainless steel
#26313
Description:
Mic stand adapter, 1 1/2" long, 5/8-27 and 3/8-16 threads Mic stand adapter, stainless steel
#28407
Description:
Replacement lock washer for SNA600 mounting kit.
#28769
Description:
Antenna mounting stud/thread adapter, stainless steel with hex socket for mounting and removal, 3/8"-16
NOTE: 3/8"-16 is included with remote antenna.
#28770
Description:
Antenna mounting stud, stainless steel with hex socket for mounting and removal. Stud side coated with red Loctite, 1/4"-20
#28790
Description:
Replacement nut for SNA600 mounting kit. 3/8"-16 Stainless Stell hexnut.
#ACOAXBNC (Specify Block)
Description:
This coaxial design is approximately 48 inches in overall length, with an right angle BNC connector. The other end is cut to a 1/4 wavelength of the corresponding frequency block with a color band and tag specifying its block. It is especially useful for applications where a small remote antenna is desired.
Coaxial antenna usage guide (PDF)
#ACOAXTX (Specify Block)
Description:
This coaxial design is approximately 36 inches in overall length, with an SMA connector. The other end is cut to a 1/4 wavelength of the corresponding frequency block with a color band and tag specifying its block. It is especially useful for applications where a small remote antenna is desired.
Coaxial antenna usage guide (PDF)
#ALP500
Description:
Standard remote antenna ideal for fixed applications. The ALP Series antennas are a Log Periodic Dipole Array (LPDA) design that provides a useful directional pattern over a broad frequency bandwidth.
Click here to view data sheet
#ALP620
Description:
Skeletal remote antenna for decreased wind loading. The ALP Series antennas are a Log Periodic Dipole Array (LPDA) design that provides a useful directional pattern over a broad frequency bandwidth.
Click here to view data sheet
#ALP650
Description:
Skeletal design remote antenna with onboard amplifier ideal for long cable runs, phantom powered from Venue, UMC16 or Bias T. The ALP Series antennas are a Log Periodic Dipole Array (LPDA) design that provides a useful directional pattern over a broad frequency bandwidth.
Click here to view data sheet
#ALP700RK
Description:
Rod repair kit for the older log periodic ALP700/ALP700a antenna. It is stronger than the original rods with a strain relief to prevent cracking failure at the thread and boom intersection.
Click here to view data sheet
#ALPKIT
Description:
Accessory mounting kit for the ALP antennas and the SNA antenna. All the parts are very rugged stainless steel and will match various mic stands and lighting stands. The threaded stud is used to join various combinations of the parts in the kit.
Click here to view data sheet
#ARG100
Description:
A 100 foot antenna cable of Belden 9913F low-loss coax cable with BNC connectors at each end. Double shielded, flexible, 50 Ohms, with a foamed polyethylene dielectric. Lower loss (3 to 4 dB) with somewhat less weight than standard RG-8 with the same 0.400" diameter.
Click here for ARG models comparison chart and Technical Data
See also:
ARG2 - 2' antenna cable of standard RG-58 coax cable
ARG2RT - 24" coaxial RF cable with right angle BNC male at both ends
ARG15 - 15' ...
Read More...
#ARG15
Description:
A 15 foot antenna cable of standard RG-58 coax cable with BNC connectors at each end. Loss of 1 to 2 dB with 0.25" diameter.
Click here for ARG models comparison chart and Technical Data
See also:
ARG2 - 2' antenna cable of standard RG-58 coax cable
ARG2RT - 24" coaxial RF cable with right angle BNC male at both ends
ARG25 - 25' antenna cable of Belden 9913F low-loss coax cable
ARG50 - 50' antenna cable of Belden 9913F low-loss coax cable
ARG100 - 100' antenna cable ...
Read More...
#ARG2
Description:
A 2 foot antenna cable of standard RG-58 coax cable with BNC connectors at each end. Loss of 1 dB or less with 0.25" diameter.
Click here for ARG models comparison chart and Technical Data
See also:
ARG2RT - 24" coaxial RF cable with right angle BNC male at both ends
ARG15 - 15' antenna cable of standard RG-58 coax cable with BNC connectors
ARG25 - 25' antenna cable of Belden 9913F low-loss coax cable
ARG50 - 50' antenna cable of Belden 9913F low-loss coax cab ...
Read More...
#ARG25
Description:
A 25 foot antenna cable of Belden 9913F low-loss coax cable with BNC connectors at each end. Double shielded, flexible, 50 Ohms, with a foamed polyethylene dielectric. Lower loss (1 to 1.2 dB) with somewhat less weight than standard RG-8 with the same 0.400" diameter.
Click here for ARG models comparison chart and Technical Data
See also:
ARG2 - 2' antenna cable of standard RG-58 coax cable
ARG2RT - 24" coaxial RF cable with right angle BNC male at both ends
ARG15 - 15 ...
Read More...
#ARG2RT
Description:
24 inch coaxial RF cable with right angle BNC male at both ends; commonly used in portable bag systems.
Click here for ARG models comparison chart and Technical Data
See also:
ARG2 - 2' antenna cable of standard RG-58 coax cable
ARG15 - 15 foot antenna cable of standard RG-58 coax cable with BNC connectors
ARG25 - 25' antenna cable of Belden 9913F low-loss coax cable
ARG50 - 50' antenna cable of Belden 9913F low-loss coax cable
ARG100 - 100' antenna cable of Belden 9 ...
Read More...
#ARG50
Description:
A 50 foot antenna cable of Belden 9913F low-loss coax cable with BNC connectors at each end. Double shielded, flexible, 50 Ohms, with a foamed polyethylene dielectric. Lower loss (1.6 to 2.3 dB) with somewhat less weight than standard RG-8 with the same 0.400" diameter.
Click here for ARG models comparison chart and Technical Data
See also:
ARG2 - 2' antenna cable of standard RG-58 coax cable
ARG2RT - 24" coaxial RF cable with right angle BNC male at both ends
ARG15 - ...
Read More...
#ARX125
Description:
A 125 foot. RG-8/X Belden 9258. BNC straight connector
NOTE: 12.5 dB loss Requires RF amplifier such as the UFM230
#BIAST
Description:
The BIAS T is used to apply DC power to a coaxial antenna line for remotely powering the UFM230 filter/amp. The DC power applied to the BIAS T (9 to 16 VDC) appears on the input port of the BIAS T to power the UFM230 through the coaxial cable, but is isolated from the output port so it will not be applied to the input of the receiver.
The BIAS T is normally placed near the receiver being fed by the coaxial cable, where power is available. The UFM230 filter/amp and antenna are plac ...
Read More...
#PALP600
Description:
Zippered Cordura pouch for ALP antennas.
#PCA900
Description:
A unique and very useful design, the PCA900 antenna provides wide bandwidth and a circular pattern in a compact, rugged package. A BNC connector allows direct connection to receivers and multicouplers with standard 50 ohm coaxial cable.
Click here to view data sheet
#PF25 (Specify Block)
Description:
Passive in-line RF filter with 25MHz passband. Passive in-line RF filter with 50MHz passband and DC Bias insertion point. Designed for use with VRMWB and VRField WB wide-band receiver systems in cases where the full bandwidth of the receiver is not needed. Specify two-block range when ordering. Specify block when ordering.
Click here for Data Sheet
#PF50 (Specify Blocks)
Description:
Passive in-line RF filter with 50MHz passband and DC Bias insertion point. Passive in-line RF filter with 50MHz passband and DC Bias insertion point to power remote amplifiers or active antennas. Designed for use with VRMWB and VRField WB wide-band receiver systems in cases where the full bandwidth of the receiver is not needed. Specify contiguous two-block range when ordering.
Click here for data sheet
#SNA600
Description:
Adjustable Dipole Antenna
The SNA600 antenna is a versatile tool for use with wireless microphone receivers or IFB transmitters. The center frequency of its 100 MHz bandwidth is tunable from 550 to 800 MHz. The frequency is set by adjusting the dipole elements using the scale printed on the body of the antenna. The elements fold for storage.
Click here for technical data sheet
#UFM230
Description:
The UFM230 provides a unique solution for antenna systems requiring long cable runs or distribution to multiple receivers or locations. The amplifier in the unit provides 12 dB of gain without attenuation. Gains of 5 dB and 8 dB can also be selected using the supplied attenuators. The built-in filters provide a 230 MHz passband.
To determine the correct attenuator for a particular application, first determine the total dB loss due to connectors, splitters, cabling, etc. The abov ...
Read More...
#UFM50
Description:
The UFM50 amplifier provides 12 dB of gain without attenuation. Gains of 5 dB and 8 dB can also be selected using the supplied attenuators. The built-in filters provide a 50 MHz passband.
Click here for technical data sheet
#ZFSC41
Description:
Four-way passive RF splitter, 1-1000 MHz, Isolation dB (Lower=25, Mid-23, Upper=20). Loss at each output dB (L=6.4, M=6.6, U=7.6). Identical to MiniCircuits model.
Click here for data sheet
#ZFSC843
Description:
Eight-way passive RF splitter, 10-1000 MHz, Isolation dB (Lower=23, Mid-25, Upper=26).Loss at each output dB (L=10.0, M=10.4, U=11.1). Identical to MiniCircuits model.
Click here for data sheet
#ZSC24
Description:
Two-way passive RF splitter, 10-1000 MHz, Isolation dB (Lower=25, Mid-35, Upper=25). Loss at each output dB (L=3.2, M=3.5, U=3.7). Identical to MiniCircuits model.
Click here for data sheet
