R400a
#35679
Description:
Lectrosonics screwdriver and adjustment tool for setting transmitter gain and roll-off pots as well as for setting the frequency switches on some older receivers and transmitters.
#A500RA (Specify Block)
Description:
UHF antenna, right angle BNC. Specify block such as A500RA-24 for block 24. These antennas can be used one block above and below the specified block. Color coded tip per ANSI resistor code.
#ACOAXBNC (Specify Block)
Description:
This coaxial design is approximately 48 inches in overall length, with an right angle BNC connector. The other end is cut to a 1/4 wavelength of the corresponding frequency block with a color band and tag specifying its block. It is especially useful for applications where a small remote antenna is desired.
Coaxial antenna usage guide (PDF)
#BIAST
Description:
The BIAS T is used to apply DC power to a coaxial antenna line for remotely powering the UFM230 filter/amp. The DC power applied to the BIAS T (9 to 16 VDC) appears on the input port of the BIAS T to power the UFM230 through the coaxial cable, but is isolated from the output port so it will not be applied to the input of the receiver.
The BIAS T is normally placed near the receiver being fed by the coaxial cable, where power is available. The UFM230 filter/amp and antenna are plac ...
Read More...
#CCMINI
Description:
A soft sided, padded and zippered carrying case for compact wireless systems such as the UCR400, UCR401, and other UCR units.
#CCTM400
Description:
Waterproof case for R400a and UH400a transmitter. It comes standard with the TM400 test mic system.
#DCR12/A4U
Description:
Power Supply for R400 Receiver; 90-240 VAC, 50/60 Hz input; 12 VDC (regulated), 400 mA max. output.
#MC16C
Description:
16 ft. coiled mic cord, 1/4" phone male to 1/4" phone male.
#PF25 (Specify Block)
Description:
Passive in-line RF filter with 25MHz passband. Passive in-line RF filter with 50MHz passband and DC Bias insertion point. Designed for use with VRMWB and VRField WB wide-band receiver systems in cases where the full bandwidth of the receiver is not needed. Specify two-block range when ordering. Specify block when ordering.
Click here for Data Sheet
#PF50 (Specify Blocks)
Description:
Passive in-line RF filter with 50MHz passband and DC Bias insertion point. Passive in-line RF filter with 50MHz passband and DC Bias insertion point to power remote amplifiers or active antennas. Designed for use with VRMWB and VRField WB wide-band receiver systems in cases where the full bandwidth of the receiver is not needed. Specify contiguous two-block range when ordering.
Click here for data sheet
#RMPR400-1
Description:
Rack mount kit for one R400a receiver. Has front mounted BNCs with 2 cables to connect to rear mounted R400a antenna inputs.
#RMPR400-2
Description:
Rack mount kit for two R400a receivers. Has front mounted BNCs with 4 cables to connect to rear mounted R400a antenna inputs.
#UFM230
Description:
The UFM230 provides a unique solution for antenna systems requiring long cable runs or distribution to multiple receivers or locations. The amplifier in the unit provides 12 dB of gain without attenuation. Gains of 5 dB and 8 dB can also be selected using the supplied attenuators. The built-in filters provide a 230 MHz passband.
To determine the correct attenuator for a particular application, first determine the total dB loss due to connectors, splitters, cabling, etc. The abov ...
Read More...
#UFM50
Description:
The UFM50 amplifier provides 12 dB of gain without attenuation. Gains of 5 dB and 8 dB can also be selected using the supplied attenuators. The built-in filters provide a 50 MHz passband.
Click here for technical data sheet
#UMC16B-230MHz
Description:
UHF Multi-coupler, 8ch diversity, 230MHz bandwidth
Wilkinson 1/4 wave strip-lineFilter passband: 1) UMC16B: 537 to 767 MHz, factory set2) UMC16BL: 486 to 692 MHz
Click here for instruction manual
#ZFSC41
Description:
Four-way passive RF splitter, 1-1000 MHz, Isolation dB (Lower=25, Mid-23, Upper=20). Loss at each output dB (L=6.4, M=6.6, U=7.6). Identical to MiniCircuits model.
Click here for data sheet
#ZFSC843
Description:
Eight-way passive RF splitter, 10-1000 MHz, Isolation dB (Lower=23, Mid-25, Upper=26).Loss at each output dB (L=10.0, M=10.4, U=11.1). Identical to MiniCircuits model.
Click here for data sheet
#ZSC24
Description:
Two-way passive RF splitter, 10-1000 MHz, Isolation dB (Lower=25, Mid-35, Upper=25). Loss at each output dB (L=3.2, M=3.5, U=3.7). Identical to MiniCircuits model.
Click here for data sheet
