 |
|
Belt-Pack Transmitters
Hand-Held
Plug-On
| Belt Pack Transmitters | ||||||||||
| VHF | UHF | |||||||||
| Features | M187 | UM100 | UM200C | UM250C | UM400 |
UM450 |
MM400C | LM | SM | UM700 |
| Form Factor | Belt Pack | Belt Pack | Belt Pack | Belt Pack | Belt Pack | Belt Pack | Miniature Watertight Belt Pack | Belt Pack | Belt Pack | Belt Pack |
| Compandors | Single Band | Dual Band | Dual Band | Dual Band | N/A (Note 1) |
N/A (Note 1) |
N/A (Note 1) |
N/A (Note 1) |
N/A (Note 1) |
N/A (Note 1) |
| RF Power | 50 mW | 100 mW | 100 mW | 250 mW | 100 mW | 250 mW | 100 mW | 50 mW | 100 mW | 50 mW |
| Emulation Modes | N/A | N/A | N/A | N/A | Five (Note 2) |
Five (Note 2) |
Five (Note 2) |
Five (Note 2) |
Five (Note 2) |
None |
| Operating Frequencies | 150 to 216 MHz | 537.6 to 767.9 MHz | 537.6 to 767.9 MHz | 537.6 to 767.9 MHz | 537.6 to 767.9 MHz | 537.6 to 767.9 MHz | 537.6 to 767.9 MHz | 537.6 to 767.9 MHz | 537.6 to 767.9 MHz | 563.2 to 665.5 MHz |
| Frequency Selection | N/A | 256 in 100 KHz Steps per 26 MHz Wide Block | 256 in 100 KHz Steps per 26 MHz Wide Block | 256 in 100 KHz Steps per 26 MHz Wide Block | 256 in 100 KHz Steps per 26 MHz Wide Block | 256 in 100 KHz Steps per 26 MHz Wide Block | 256 in 100 KHz Steps per 26 MHz Wide Block | 256 in 100 KHz Steps per 26 MHz Wide Block | 256 in 100 KHz Steps per 26 MHz Wide Block | 256 in 100 KHz Steps per 26 MHz Wide Block |
| Channel Spacing | 25 KHz | 100 KHz (Note 3) | 100 KHz (Note 3) | 100 KHz (Note 3) | 100 KHz (Note 3) | 100 KHz (Note 3) | 100 KHz (Note 3) | 100 KHz (Note 3) | 100 KHz (Note 3) | 100 KHz (Note 3) |
| Operating Frequency Adjustment | Fixed | Two 16-position rotary switches | Two 16-position rotary switches | Two 16-position rotary switches | Two 16-position rotary switches | Two 16-position rotary switches | Two 16-position rotary switches | Two 16-position rotary switches | Control Panel mounted membrame switches | Two 16-position rotary switches |
| Frequency Control | Crystal | Synthesized | Synthesized | Synthesized | Synthesized | Synthesized | Synthesized | Synthesized | Synthesized | Synthesized |
| Frequency Stability | ±0.005% | ±0.001% | ±0.002% | ±0.002% | ±0.002% | ±0.002% | ±0.002% | ±0.002% | ±0.002% | ±0.001% |
| Deviation | ±15 KHz (max) | ±20 KHz (max) | ±75 KHz (Max) | ±75 KHz (Max) | ±75 KHz (Max) | ±75 KHz (Max) | ±75 KHz (Max) | ±75 KHz (Max) | ±75 KHz (Max) | Digital |
| Spurious Radiation | 55 dB Below Carrier | 90 dB Below Carrier | 90 dB Below Carrier | 90 dB Below Carrier | 90 dB Below Carrier | 90 dB Below Carrier | 60 dB Below Carrier | 60 dB Below Carrier | 60 dB Below Carrier | 60 dB Below Carrier |
| Equivalent Input Noise (A-Weighted) | -126 dBV | -126 dBV | -126 dBV | -126 dBV | -120 dBV | -120 dBV | -118 dBV | -120 dBV | -125 dBV | -119 dBV |
| Transmitter Type | Analog | Analog | Analog | Analog | Digital Hybrid Wireless | Digital Hybrid Wireless | Digital Hybrid Wireless | Digital Hybrid Wireless | Digital Hybrid Wireless | Encrypted Digital |
| Audio Input Connector | 5-pin Locking (TA5F) | 5-pin Locking (TA5F) | 5-pin Locking (TA5F) | 5-pin Locking (TA5F) | 5-pin Locking (TA5F) | 5-pin Locking (TA5F) | 2.5 mm Micro (Watertight) | 5-pin Locking (TA5F) | 5-pin Locking (TA5F) | 5-pin Locking (TA5F) |
| Input Impedance | 500, 1K and 10K Ohm taps provided | 200, 1K and 10K Ohm taps provided | 500, 1K and 10K Ohm taps provided | 100, 1K and 10K Ohm taps provided | 100, 4K and 40K Ohm taps provided | 100, 4K and 40K Ohm taps provided | 2 k Ohm | 100, 4K and 40K Ohm taps provided | (Note 4) | 100, 4K and 40K Ohm taps provided |
| Input Limiter | Soft Limiter with >30 dB Range |
Soft Limiter with >30 dB Range |
Soft Limiter with >30 dB Range |
Soft Limiter with >30 dB Range |
DSP Controlled Dual Env. with >30 dB Range |
DSP Controlled Dual Env. with >30 dB Range |
DSP Controlled Dual Env. with >30 dB Range |
DSP Controlled Dual Env. with >30 dB Range |
DSP Controlled Dual Env. with >30 dB Range |
DSP Controlled Dual Env. with >30 dB Range |
| Input Level | Nominal 2 mV to 300 mV before limiting >30V with limiting |
Nominal 2 mV to 300 mV Before Limiting |
Nominal 2 mV to 300 mV before limiting >50V with limiting |
Nominal 2 mV to 300 mV Before Limiting |
Nominal 2 mV to 300 mV Before Limiting |
Nominal 2 mV to 300 mV Before Limiting |
Nominal 2 mV to 300 mV Before Limiting |
Nominal 2 mV to 300 mV Before Limiting |
(Note 5) | Nominal 2 mV to 300 mV Before Limiting |
| Low Frequency Roll Off |
-12 dB per Octave |
-18 dB per Octave, Adj from 35 Hz to 150 Hz | -18 dB per Octave, Adj from 35 Hz to 150 Hz | -18 dB per Octave, Adj from 35 Hz to 150 Hz | -18 dB per Octave, Adj from 35 Hz to 150 Hz | -18 dB per Octave, Adj from 35 Hz to 150 Hz | -12 dB per Octave at 70 Hz |
-12 dB per Octave at 70 Hz |
-12 dB per Octave at 70 Hz |
-18 dB per Octave, Adj from 35 Hz to 150 Hz |
| Gain Control | 43 dB Semi-log Rotary Control |
43 dB Semi-log Rotary Control |
43 dB Semi-log Rotary Control |
43 dB Semi-log Rotary Control |
43 dB Semi-log Rotary Control |
43 dB Semi-log Rotary Control |
43 dB Semi-log Rotary Control |
43 dB Semi-log Rotary Control |
40 dB Panel mounted membrane switch |
43 dB Semi-log Rotary Control |
| Modulation Indicators | Dual LEDs | Dual LEDs | Dual LEDs | Dual LEDs | Dual Bi-Color LEDs |
Dual Bi-Color LEDs |
Dual Bi-Color LEDs |
Dual Bi-Color LEDs |
Dual Bi-Color LEDs |
Dual Bi-Color LEDs |
| Pilot Tone | No | No | 32 kHz | 32 kHz | Yes (Note 6) |
Yes (Note 6) |
Yes (Note 6) |
Yes (Note 6) |
Yes (Note 6) |
N/A |
| Frequency Response | 100 Hz to 15K kHz | 80Hz to 20 kHz | 50 Hz to 20 kHz | 50 Hz to 20 kHz | 32 Hz to 20 kHz | 32 Hz to 20 kHz | 32 Hz to 20 kHz | 90 Hz to 20 kHz | 70 Hz to 20 kHz | 50 Hz to 22 kHz |
| Output Antenna | Integrated in Mic Cable | Fixed Flexible Whip | Detachable Flexible Whip with SMA Connector | Detachable Flexible Whip with SMA Connector | Detachable Flexible Whip with SMA Connector | Detachable Flexible Whip with SMA Connector | Fixed Flexible Whip | Fixed Flexible Whip | Fixed Flexible Unbreakable Steel Cable | Detachable Flexible Whip with SMA Connector |
| Power Requirements | 9 Volt Alkaline | 9 Volt Alkalline or Lithium | 9 Volt Alkalline or Lithium | 9 Volt Alkalline or Lithium | 9 Volt Alkalline or Lithium | 9 Volt Alkalline or Lithium | 1.5 V AA Alkalline or Lithium | 9 Volt Alkalline or Lithium | 1.5 V AA Alkalline, Lithium or NiMH | 9 Volt Alkalline or Lithium |
| Battery Life (hours) | 14 (alk) | 4.5 (alk) 14 (lith) |
4.5 (alk) 14 (lith) |
2 (alk) 7 (lith) |
5 (alk) 10 (lith) |
1.5 (alk) 3.5 (LiPoly) |
2 (alk) 4.5 (lith) |
6 (alk) 13 (lith) |
1.5 (alk) 5.5 (lith) 4 (NiMH) |
4.5 (alk) 14 (lith) |
| Housing | Machined Aluminum | Machined Aluminum | Machined Aluminum | Machined Aluminum | Machined Aluminum | Machined Aluminum | Machined Aluminum | Machined Aluminum | Machined Aluminum | Machined Aluminum |
| Weight (Includes Battery) | 5.3 oz | 6.3 oz. | 6.3 oz. | 6.6 oz. | 6.98 oz | 6.98 oz | 3.6 oz. | 6.3 oz. | 2.7 oz. | 6.3 oz. |
| Size | 3.25x2.375 x0.75 inches | 3.1x2.4 x.75 inches | 3.1x2.4 x.75 inches | 3.1x2.4 x.75 inches | 3.17x2.84 x.84 inches | 3.17x2.84 x.84 inches | 2.55x1.99 x.0.69 inches | 3.1x2.4 x.75 inches | 2.3x1.8 x.64 inches | 3.1x2.4 x.75 inches |
Notes:
- Digital Hybrid Wireless™ technology negates the need for compandors or their artifacts.
- Digital Hybrid Wireless™ systems can emulate all Lectrosonics wireless analog components, including IFB, plus many wireless analog components from other vendors. (Call Lectrosonics for more details.)
- 25 KHz spacing is available in Europe through authorized Lectrosonics Service Centers. Contact our sales staff for more details.
- Dynamic Mic: 300 Ohms
Electret Lavaliere: Virtual Ground with servo adjusted contant current bias
Line Level: 2.7 kOhms
- If set for dynamic mic: 0.5 mV to 50 mV before limiting; greater than 1 V with limiting.
If set for electret lavalier: 1.7 uA to 170 uA before limiting; freater than 5000 uA (5 mA) with limiting.
Line Level: 5.0 mV to 500 mV (0.5 V) befroe limiting; greater than 15 V with limiting. - Depending on the Compatibility Mode selected, Digital Hybrid Wireless (400 Series) transmitters can produce pilot tones for other Digital Hybrid Wireless (400 Series) systems, or 200 Series analog systems.
- The digital encryption key is used to control the receiver, thus negating the need for a pilot tone
Back to Top of Page
| Hand-Held Transmitters | ||
| UHF | ||
| Features | UT400VM | UT700 |
| Transmitter Type | Digital Hybrid Wireless | Encrypted Digital |
| RF Power | 100 mW | 50 mW |
| Standard Capsule (Note 1) |
Varimic™ | Varimic™ |
| Compandors | N/A (Note 2) |
N/A (Note 2) |
| Operating Frequencies | 537.6 to 793.5 MHz | 563.2 to 665.5 MHz |
| Frequency Selection | 256 in 100 KHz Steps per 26 MHz Wide Block | 256 in 100 KHz Steps per 26 MHz Wide Block |
| Channel Spacing | 100 KHz | 100 KHz |
| Frequency Control | Synthesized | Synthesized |
| Operating Frequency Adjustment | Two 16-position rotary switches | Two 16-position rotary switches |
| Frequency Stability | ±0.002% | ±0.001% |
| Deviation | ±75 KHz (max) | Digital |
| Spurious Radiation | 90 dB Below Carrier | 70 dB Below Carrier |
| Equivalent Input Noise (A-Weighted) | -120 dB | -119 dB |
| Input Impedance | DSP Controlled Dual Env. with >30 dB Range |
DSP Controlled Dual Env. with >30 dB Range |
| Tone Adjustment | Internal (In Mic Capsule) |
Internal (In Mic Capsule) |
| Gain Control | Internal 43 dB Semi-log Rotary Control |
Internal 43 dB Semi-log Rotary Control |
| Modulation Indicators (Internal) | Dual Bi-Color LEDs |
Dual Bi-Color LEDs |
| Low Frequency Roll Off | 36 dB per Octave, 35 to 70 Hz | 36 dB per Octave, 35 to 70 Hz |
| Pilot Tone | Yes (Note 4) |
N/A (Note 5) |
| Emulation Modes | Five (Note 6) |
No |
| Frequency Response | 80 Hz to 20 kHz ±1 dB |
75 Hz to 20 kHz ±1 dB |
| Power Requirements | 9 Volt Alkalline or Lithium | 9 Volt Alkalline or Lithium |
| Battery Life (hours) | 3.5 (alk) 6.5 (lith) |
3.5 (alk) 6.5 (lith) |
| Housing | Machined PVC | Machined PVC |
| Weight (Includes Battery) | 12.4 oz. | 12.4 oz. |
| Size | 9 inches x2.05 inch dia. | 9 inches x2.05 inch dia. |
Notes:
- Several optional microphone capsules are available with the UT400 and UT700 Hand-Held Microphones, including the
Lectrosonics VariMicTM and AKG C5900 models. Call Lectrosonics for more details about optional microphone capsules.
- Digital Hybrid Wireless™ technology negates the need for compandors or their artifacts.
- 25 KHz spacing is available in Europe through authorized Lectrosonics Service Centers. Contact our sales staff for more details.
- Depending on the Compatibility Mode selected, Digital Hybrid Wireless (400 Series) transmitters can produce pilot
tones for other Digital Hybrid Wireless (400 Series) systems, or 200 Series analog systems.
- The digital encryption key is used to control the receiver, thus negating the need for a pilot tone
- Digital Hybrid Wireless™ systems can emulate all Lectrosonics wireless analog components, including IFB, plus many wireless analog components from other vendors. (Call Lectrosonics for more details.)
Back to Top of Page
| Plug-On Transmitters | |||
| VHF | UHF | ||
| Features | H187 | UH400A | UH400TM |
| Transmitter Type | Analog | Digital Hybrid Wireless | Digital Hybrid Wireless |
| RF Power | 50 mW | 100 mW | 100 mW |
| Operating Frequencies | 150 to 216 MHz | 537.6 to 767.9 MHz | 537.6 to 767.9 MHz |
| Frequency Selection | N/A | 256 in 100 KHz Steps per 26 MHz Wide Block | 256 in 100 KHz Steps per 26 MHz Wide Block |
| Channel Spacing | 25 kHz | 100 KHz | 100 KHz |
| Operating Frequency Adjustment | Fixed | Two 16-position rotary switches | Two 16-position rotary switches |
| Frequency Control | Crystal | Synthesized | Synthesized |
| Frequency Stability | ±0.005% | ±0.002% | ±0.002% |
| Deviation | ± 15 kHz | Digital | Digital |
| Spurious Radiation | 55 dB Below Carrier | 60 dB Below Carrier | 60 dB Below Carrier |
| Equivalent Input Noise (A-Weighted) | -112 dBV | -118 dBV | -118 dBV |
| Input Impedance | 1 K Ohm | 1 K Ohm | 1 K Ohm |
| Input Level | Nominal 4 mV to 300 mV Before Limiting 10 V max. with limiting |
Nominal 2 mV to 300 mV Before Limiting |
Nominal 2 mV to 300 mV Before Limiting |
| Input Limiter | Soft Limiter wtith >30 dB Range |
DSP Controlled Dual Env. with >30 dB Range |
DSP Controlled Dual Env. with >30 dB Range |
| Input Connector | 3-pin, female XLR | 3-pin, female XLR | 3-pin, female XLR |
| Gain Control | 43 dB Semi-log Rotary Control |
43 dB Semi-log Rotary Control |
43 dB Semi-log Rotary Control |
| Modulation Indicators | Dual LEDs | Dual Bi-Color LEDs |
Dual Bi-Color LEDs |
| Compandors | Single | None (Note 1) |
None (Note 1) |
| Low Frequency Roll Off | -12 dB per Octave -3 dB at 90 Hz |
-12 dB per Octave, 70 Hz |
-12 dB per Octave, 70 Hz |
| DSP | N/A | 32 to 20K | 32 to 20K |
| Pilot Tone | N/A | Yes (Note 2) |
Yes (Note 2) |
| Emulation Modes | None | Yes (Note 3) |
Yes (Note 3) |
| Frequency Response | 100 Hz to 15 kHz | 90 Hz to 20 kHz ±1 dB |
40 Hz to 20 kHz ±1 dB |
| Phantom Power | 5 V | 5. 18 and 48 V (selectable) | 5. 18 and 48 V (selectable) |
| Power Requirements | 9 Volt Alkalline or Lithium | 9 Volt Alkalline or Lithium | 9 Volt Alkalline or Lithium |
| Battery Life (hours) | 14 (alk) | 4.5 (alk) 12 (lith) |
4.5 (alk) 12 (lith) |
| Housing | Machined Aluminum | Machined Aluminum | Machined Aluminum |
| Weight (Includes Battery) | 7 oz. | 6.6 Oz | 6.6 Oz |
| Size | 1.5x1.5 x4.2 inches | 1.5x1.65 x4.2 inches | 1.5x1.65 x4.2 inches |
Notes:
- Digital Hybrid Wireless™ technology negates the need for compandors or their artifacts.
- Depending on the Compatibility Mode selected, Digital Hybrid Wireless (400 Series) transmitters can product pilot
tones for other Digital Hybrid Wireless (400 Series) systems, or 200 Series analog systems.
- Digital Hybrid Wireless™ systems can emulate all Lectrosonics wireless analog components, including IFB, plus many wireless analog components from other vendors. (Call Lectrosonics for more details.)
Back to Top of Page